Try Latest Cisco 100-105 Exam Questions – Pass In First Attempt

100-105 Braindumps 100-105 dumps 100-105 Exam 100-105 Exam Dumps 100-105 Practice Test 100-105 Questions Cisco

Success in Cisco Certified Design Associate 100-105 exam is 100% by preparing the up-to-date 100-105 exam questions and doing practice through best practice 100-105 exam test software. Cisco Interconnecting Cisco Networking Devices Part 1 100-105 exam dumps material leads towards success by doing practice with 100-105 exam test software and you leave no room to miss any key aspect of the 100-105 exam because of the real simulation software. Before purchase of the actual Cisco 100-105 exam you can take 100-105 exam demo free of cost!

100-105 exam questions, 100-105 PDF dumps; 100-105 exam dumps:: (347 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate Cisco 100-105 Dumps Exam Questions and Answers:

Version: 12.0
Question: 21

Refer to the exhibit.

If the resume command is entered after the sequence that is shown in the exhibit, which router prompt will be displayed?

A. Router1>
B. Router1#
C. Router2>
D. Router2#

Answer: C

After resuming the telnet session by using the Enter key after it has been suspended, it will resume back to the telnet session so it will be back to the router2> prompt.

Question: 22

Refer to the exhibit.

Which default gateway address should be assigned to HostA?


Answer: B

The default gateway will be the IP address of the router that it connects to, not the switch.

Question: 23

Which OSI layer header contains the address of a destination host that is on another network?

A. application
B. session
C. transport
D. network
E. data link
F. physical

Answer: D

Only network address contains this information. To transmit the packets the sender uses network address and datalink address. But the layer 2 address represents just the address of the next hop device on the way to the sender. It is changed on each hop. Network address remains the same.

Question: 24

Which layer of the TCP/IP stack combines the OSI model physical and data link layers?

A. Internet layer
B. transport layer
C. application layer
D. network access layer

Answer: D

The Internet Protocol Suite, TCP/IP, is a suite of protocols used for communication over the internet. The TCP/ IP model was created after the OSI 7 layer model for two major reasons. First, the foundation of the Internet was built using the TCP/IP suite and through the spread of the World Wide Web and Internet, TCP/IP has been preferred. Second, a project researched by the Department of Defense (DOD) consisted of creating the TCP/IP protocols. The DOD’s goal was to bring international standards which could not be met by the OSI model.
Since the DOD was the largest software consumer and they preferred the TCP/IP suite, most vendors used this model rather than the OSI. Below is a side by side comparison of the TCP/IP and OSI models.

Question: 25

Which protocol uses a connection-oriented service to deliver files between end systems?


Answer: C

TCP is an example of a connection-oriented protocol. It requires a logical connection to be established between the two processes before data is exchanged. The connection must be maintained during the entire time that communication is taking place, then released afterwards. The process is much like a telephone call, where a virtual circuit is established–the caller must know the person’s telephone number and the phone must be answered–before the message can be delivered.
TCP/IP is also a connection-oriented transport with orderly release. With orderly release, any data remaining in the buffer is sent before the connection is terminated. The release is accomplished in a three-way handshake between client and server processes. The connection-oriented protocols in the OSI protocol suite, on the other hand, do not support orderly release. Applications perform any handshake necessary for ensuring orderly release.
Examples of services that use connection-oriented transport services are telnet, rlogin, and ftp.

Question: 26

Refer to the exhibit.

If the hubs in the graphic were replaced by switches, what would be virtually eliminated?

A. broadcast domains
B. repeater domains
C. Ethernet collisions
D. signal amplification
E. Ethernet broadcasts

Answer: C

Modern wired networks use a network switch to eliminate collisions. By connecting each device directly to a port on the switch, either each port on a switch becomes its own collision domain (in the case of half duplex links) or the possibility of collisions is eliminated entirely in the case of full duplex links.

New Updated 100-105 Exam Questions 100-105 PDF dumps 100-105 practice exam dumps: