Try Latest Cisco 300-080 Exam Questions – Pass In First Attempt

300-080 Braindumps 300-080 dumps 300-080 Exam 300-080 Exam Dumps 300-080 Practice Test 300-080 Questions Cisco

Success in Cisco Certified Network Professional Collaboration 300-080 exam is 100% by preparing the up-to-date 300-080 exam questions and doing practice through best practice 300-080 exam test software. Cisco Troubleshooting Cisco IP Telephony and Video 300-080 exam dumps material leads towards success by doing practice with 300-080 exam test software and you leave no room to miss any key aspect of the 300-080 exam because of the real simulation software. Before purchase of the actual Cisco 300-080 exam you can take 300-080 exam demo free of cost!

♥♥ 2018 NEW RECOMMEND 300-080 Exam Questions ♥♥

300-080 exam questions, 300-080 PDF dumps; 300-080 exam dumps:: https://www.dumpsschool.com/300-080-exam-dumps.html (157 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate Cisco 300-080 Dumps Exam Questions and Answers:

Version: 10.0
Question: 21

A user is dialing an external PSTN number with a prefix of 01 from a Cisco TelePresence SX10 Quick Set in a Cisco VCS environment. In the past, the Cisco VCS and the ISDN gateway were correctly configured with a prefix of 01, but the calls are now failing. What are three possible causes? (Choose three.)

A. The Cisco VCS Control is down.
B. The interworking setting is turned off.
C. The audio feature in the Cisco TelePresence SX10 is turned off.
D. The SIP trunk is not configured on the gateway.
E. 01 is not a valid prefix.
F. ISDN is not enabled on the Cisco TelePresence SX10.
G. The Cisco TelePresence SX10 is not registered to the Cisco VCS Control.
H. The Cisco TelePresence SX10 is not registered to the Cisco Express C.

Answer: A, B, G

Question: 22

Endpoint A is registered to Cisco Unified Communications Manager as S1@company.com. It is trying to call Endpoint B, which is registered to the same company’s Cisco VCS Control with an H.323 ID of S2.internal@company.com. The route pattern is set to “*.*” and is pointed to a SIP trunk to the Cisco VCS Control. The search rule for (.*).internal@company.com is set to search the local zone. The call does not work. What is a possible reason?

A. There is no search pattern to route the call to System B.
B. There is no valid route pattern to route from System A to System B.
C. System B is registered as H.323 and needs to use an E.164 alias number only.
D. The Cisco VCS Control should be neighbor to the Cisco Unified Communications Manager.
E. You need an MGCP gateway to route from the Cisco Unified Communications Manager to the Cisco VCS Control.
F. The Cisco VCS Control is missing the Cisco Unified Communications Manager interop option.
G. The Cisco VCS Control is missing the interworking option.

Answer: G

Question: 23

You configured a Cisco ISR G2 as a SIP gateway, but the gateway does not show that it is registered with Cisco Unified Communications Manager. What is causing this issue?

A. Cisco Unified Communications Manager does not support SIP gateways.
B. The gateway does not have the UC license installed.
C. The gateway does not have Cisco Unified Border Element session licensing.
D. Cisco Unified Communications Manager does not show a SIP gateway as registered if it is not properly configured.
E. Cisco Unified Communications Manager never shows a SIP gateway as registered even when it is properly configured.
F. The Cisco ISR G2 cannot be a SIP gateway.

Answer: E

Question: 24

Which issue would cause an MGCP gateway to fail to register with Cisco Unified Communications Manager?

A. missing the configuration command isdn bind-l3 ccm-manager under the ISDN interface
B. mismatched domain name on the MGCP gateway and Cisco Unified Communications Manager gateway configuration
C. misconfigured route group in Cisco Unified Communications Manager
D. incorrect MGCP IP address specified in the gateway configuration in Cisco Unified Communications Manager

Answer: B

Question: 25

Endpoints are configured for both H.323 and SIP using the same URI and Cisco VCS settings, but the endpoints register only as H.323 endpoints. What is causing this issue?

A. A firewall is blocking all traffic from the endpoints to the Cisco VCS.
B. The Cisco VCS has no SIP domains configured.
C. The Cisco VCS is blocking the endpoints because of duplicate ID entries.
D. The endpoints do not have the SIP option key installed.
E. SIP does not work, because SIP is used for Cisco Unified Communications Manager registration only.

Answer: B

Question: 26

You are trying to register an H.323-based Cisco TelePresence system to Cisco Unified Communications Manager and a Cisco DX70 system to the Cisco VCS Control. Why do neither of the units want to register?

A. The H.323-based system needs an E164 number to register to Cisco Unified Communications Manager, and the Cisco DX70 needs to have the MAC address configured first on the Cisco VCS Control.
B. The H.323-based system needs to register to the Cisco VCS Control with an E.164 number, and the Cisco DX70 needs the TFTP address to register on the Cisco Unified Communications Manager.
C. Both systems need to register to the Cisco VCS Control, but the H.323-based system needs to have the gatekeeper setting set to “Direct.”
D. Both systems need to register to the Cisco Unified Communications Manager, as the Cisco VCS Control is used only for firewall traversal.
E. You need Cisco TelePresence Management Suite to register Cisco TelePresence systems.
F. You need Cisco TelePresence Server to register Cisco TelePresence systems.

Answer: B

New Updated 300-080 Exam Questions 300-080 PDF dumps 300-080 practice exam dumps: https://www.dumpsschool.com/300-080-exam-dumps.html