Success in AIX V1 C9010-022 exam is 100% by preparing the up-to-date C9010-022 exam questions and doing practice through best practice C9010-022 exam test software. IBM AIX Administration V1 C9010-022 exam dumps material leads towards success by doing practice with C9010-022 exam test software and you leave no room to miss any key aspect of the C9010-022 exam because of the real simulation software. Before purchase of the actual IBM C9010-022 exam you can take C9010-022 exam demo free of cost!
C9010-022 exam questions, C9010-022 PDF dumps; C9010-022 exam dumps:: https://www.dumpsschool.com/C9010-022-exam-dumps.html (62 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)
Latest and Most Accurate IBM C9010-022 Dumps Exam Questions and Answers:
A server on the 165.x.x.x subnet is displaying network problems. The administrator uses a console connection and gathers the following information:
Which action will permanently resolve the issue?
A. Flush the routing table.
B. Run ‘route del 10.2.98.113-f.
C. Modify/etc/routes and reboot the system.
D. Run ‘chdev-I inet0-a delroute=net.-hopcount,0,,0.10.2.98.113’.
Paging space on a system is almost entirely consumeD. What temporary solution can be used to prevent the system from sending SIGKILL to processes while the administrator performs more in-depth problem determination?
A. Use swapon to flush paging space entries to physical memory.
B. Use tuning commands to change the system behavior so it does not terminate processes
C. Increase the existing paging space.
D. Use tuning commands to set the page space kill threshold to 100%.
New Updated C9010-022 Exam Questions C9010-022 PDF dumps C9010-022 practice exam dumps: https://www.dumpsschool.com/C9010-022-exam-dumps.html
A host has a single virtual Ethernet adapter (ent0) configured with only a default PVID, and the administrator is trying to determine why it cannot be used to reach any other system on the network. He suspects that it may be caused by a problem in the VLAN configuration.
How would the administrator determine the VLAN for which the adapter was configured?
A. Use the command ‘Isdev -I ent0’ on the host to determine the port VLAN ID.
B. Use the command ‘Isattr-EI ent0’ on the host to determine the port VLAN ID.
C. Look on the HMC to determine which VLAN is configured for the adapter.
D. Examine the Shared Ethernet Adapter on the Virtual I/O Server to determine which VLAN the adapter is using.
How can an administrator disable Role Based Access Control (RBAC) in a WPAR?
A. Run chattr -E -I sys0 -a enhanced_RBAC=false
Reboot the WPAR
B. Run the RBAC wizard and deselect ‘Enable RBAC
Reboot the system
C. Run chdev -I mywpar -a enhanced_RBAC=false
Reboot the Global Environment
D. Run chwpar -a RBAC=false
Reboot the WPAR
After performing a NIM rte install, the administrator noticed that not all filesets are at the correct Technology Level (TL). What action will help the administrator determine why the inconsistent fileset levels were installed?
A. On the NIM server, run an Ippchk to identify if the Software Vital Product Data is valid.
B. On the NIM client, run oslevel command against the TL to identify missing prerequisites.
C. Run instfix command on NIM client to determine what filesets are inconsistent.
D. On the NIM server run the NIM IsIpp command to indentify downlevel filesets contained in the lpp_source.
What is a requirement for Live Partition Mobility?
A. The network and disk must be virtual.
B. The disk must be virtual and a Logical Host Ethernet Adapter (LHEA) for network.
C. The client partition must be connected to a SAN.
D. The client partition must be set up as a ‘Mover Service Partition’.